Hello everyone, I’m doing some box cleaning and I found a bunch of cables which I’ll ask for your help for identification, if you don’t mind 🙃
So, as the title says, how do you call this cable?
Thank you!
You must log in or register to comment.
somewhat related PSA: never use old psu cables with a different model psu. As far as I understand it they aren’t standardized as to which wires connect which pins, so you risk destroying components if you mix and match cables and psu
This.
I would personally call OP’s cable “house-fire”
Nah it’s fine. Even if he plugs in only one of the 6 pins it’s more than capable of the 150w the 8 pin output is rated for. You’d need a really old and shitty PSU for it to actually use different gauge wires for the 6 Vs 8 pin, since the only difference is 2 extra ground wires (and a higher power rating).
A house fire is unlikely, as you definitely have the PC under supervision on first power-on. The wire insulation can catch fire under certain circumstances but it won’t burn your house down if you’re quick to act.
No, don’t throw them away. You can definitely replace one with another if all the wire colors match and the wires are thick enough and by a reputable brand (so that it’s actual copper). But yes, 4-, 6- and 8-pin Molex connectors have at least 2 different possible pinouts, the 24-pin one should be standard.
But if you’re naïve and think they’re plug-and-play, you’ll be playing with a plug-and-fire setup. Most of such swaps will cause a short circuit, in which case fuses or electronic protection will probably trip before the cable insulation starts burning (if the copper is thick enough to sustain 100 A for a second and not heat up by 200 °C). However, pretty much no PC components have polarity protection so you will need to go shopping for an entirely new build.
I’m not one the throw things away, but please don’t reuse them if you don’t know what your doing.
The PSU end of PSU cables are usually different from brand to brand, sometimes model to model (thanks Corsair), so yeah as long as the pinout matches you should be fine, but I usually wouldn’t risk it. Oh the cables are usually all black too, so good luck toneing it out with a multimeter.
For example Corsair vs Seasonic, pay attention to the PSU side:
Yeah, check any documentation available and even check which pins are connected to the same voltage rails. In this case, common sense says that the GPU most likely be fine as long as it uses less than 2/3 the rated power of the cable but any drives will pop.
Thanks for the info, everyone!
I made full custom cables for my last build then the PSU died. RMAed it and got a replacement that was on generation newer.
If I hadn’t have learned that cables weren’t standardized while making the first batch, I would have fried everything in my PC.
I never wound up remaking/rerouting everything so it just looked like shit for the following 2 years. I probably won’t make custom cables again for that reason, though it did look really nice
Its for this reason i use straight-through extensions when builing my PC. Lets me route cables where/how i want. Then they connect to the psu cables somewhere sensible and hidden. Adds to the cost but makes the whole build (so upgrades/replacement) so much more modular.
Just have to make sure you get decent ones and not thin core cheap crap.
I almost did the same as you, and decided to beep out some of tge psu cables as i was waiting for the new PSU to arrive. Immediately bought straight extensions, and havent looked back since!I just went with all black this time to skip out on all of it lol
Pretty much everything is hidden so I used to stock cables
Wow, never new about this, rather important to know about this actually.
I’ve absolutely fried a brand new HDD in my server because of this. I thought it was a cable for that PSU, but it was a different brand.
Most likely, the motor and head circuitry survived. The burnt PCB can probably be cheaply replaced without cracking open the sealed internals of the drive mechanism, and the drive should work as normal after a test and calibration. Of course, wrong polarity will destroy SSDs and most other PC parts beyond the point of repair.
It’s always safer to just leave random mystery cables alone.
However, if you have a multimeter and some patience, they can still be used safely. You just need to know what you’re doing, look up the pinout and measure the voltages before plugging anything into any sensitive components.
Not planning to plug anything :D Just want to get rid of some stuff and I need to somehow label it. Thanks for the info though!
That sucks. Glad I saw your comment. Hope I remember when it matters.
It’s a power adapter cable for inside a PC. It’s an 8 pin to dual 6 pin PCI power adapter. You probably don’t need it, it likely came with a PSU and wasn’t needed for the build.
I definitely don’t need it, just want to label it somehow, thanks for the info!
GPU Molex 8 pin (6+2) PCI Express male to 2 x Dual PCIe 6 pin Female Graphics Video Card PCI-E VGA Splitter Hub Power Cable (Some of the keywords like “VGA Splitter” are misleading or duplicate but most of it is correct)
That’s a very catchy name :) Just rolls of the tongue
You can call it Greg.
Diky moc!
Dual 6 pin to 8 pin adaptor.
Generally used for high end video cards.
Older higher end video cards. Back in the day when a single 8 pin pcie cable wasn’t a given on your PSU so manufacturers just shipped that adapter.
Now we have the abomination that’s the 4x 8 pin to 12vhpwr and takes up 10 feet of space.
This your card?
Can it run Crysis?
still no
I think I’d go with something like Tedly or Lawrence.
I was thinking Emilio.
Puuhöylä
Ei ole puuhöylä
No haista vittu sitte
He he he he
prkl xd
Dunno what they are actually called (and I refuse to look it up) but I always called those 6 pin and 8 pin power connectors and people seem to know what I mean.
That is how I always called them as well, so we’re good :D
Except there are several types with different pinouts, and you can destroy components with reverse polarity.
Hasn’t really been an issue in the last 20 years for me and now those are really only used for the CPU power and AMD GPUs. Also aren’t those curved pin cover things there specifically so you couldn’t plug it into the wrong thing?
No, the manufacturers haven’t standardized the pinout of physically connectible 6-pin and 8-pin connectors. Look at other comments like this one.
Oh yea, don’t mix and match PSU cables, that’s pretty common knowledge, just use the cables that come with the PSU and you’re fine though. The adapter on the picture used to be pretty common and came with the PSU before modular PSUs became the norm though, not really used anymore from what I have seen.
It’s an adapter for the power to a graphics card.
Most modern cards need the combined power of the two input cables, while many power supply units for compatibility’s sake still only offer the two small cables and not a single big one.
So this adapter now usually comes with every graphics card you buy, and sometimes PSUs too, and they end up lying around.
Yeah, this definitely ended up lying around, thanks for the info!
Chuck for sure. Then you don’t have to worry about a name.
xd
You don’t need it; just toss/donate/recycle it.
Any adapter you might need for a new GPU in the future will already be in the box.
That’s what I’m planning to do, however, I needed a name for posting it xd
No way! I just used one today with my second-hand GPU! Now I just have to figure out why it won’t boot…
Do I need to place the picture either in the title or in the post? Sorry, I’m noob here lmao
The way you posted it was fine
Thanks xd
It looks like a power connector used inside of an PC. I think they’re called (number)+ pin power connector. Have a look at this
Thank you!
Dave Or Davette
I thought it was Bob.
I used to call it Pepe
